web analytics

Archive | September, 2017

Bargain or Just Cheap? – RUIKE Hornet F815

Welcome to Bargain or Just Cheap? This series will review budget friendly knives for a variety of uses in a short format. All of the knives will cost less than $50 (in most cases, much less) and will be purchased out of my own pocket. I’ll buy them, carry them, and use them in an attempt to determine if the knife is a bargain or just cheap.


You would think that it would be easier to find bargain fixed blades than it is to find bargain folding knives due to the simplicity of a fixed blade knife. However, that isn’t always the case for one reason – sheaths. Most bargain knives come with terrible sheaths and by the time you replace the lousy included the sheath, the knife isn’t a bargain anymore. It takes a little digging but there are bargains out there beyond the standby Mora.

RUIKE Knives is kind of like the knife division of Fenix Lights though their affiliation with the flashlight maker isn’t always spelled out clearly on their website. They make a number of interesting and value minded knives but there is one in particular, the RUIKE Hornet F815, that drew me in several months ago.

Specs:

Steel: Sandvik 14C28N

Handle: Textured G-10

Blade length: 3.35 in.

Spine Thickness: .14 in.

Overall length: 7.48 in.

Weight: 3.7 oz.

Sheath: Injection molded

Observation from Use

I was initially drawn to the Hornet because I was looking for a full sized fixed blade knife that was both stout and lightweight. I like flat grinds and drop point blade shapes for general use. The Hornet seemed to hit all those points. It has been on several adventures since then, spending a lot of time tucked into a Hill People Gear Runner’s Kit Bag, and has served me well.

The Hornet is relatively lightweight while still offering the durability and comfort of a full tang knife with slab handles. The knife’s most distinctive feature is its skeletonized handle with textured G-10 slabs. This feature is VERY well executed. They slabs are fit to the tang very well and RUIKE even took steps to chamfer the edge of the G-10 inside the lightening cutout. The result is a knife that is lightweight for this type of construction, more comfortable to use than a knife without handle slabs, and that offers great grip even with gloves.

RUIKE uses Sandvik 14C28N at .14″ thick on the Hornet. Sandvik 14C28N is a great steel that takes a fine edge without much fuss. This knife cuts and slices well at .14″ thick and with the relatively tall, flat saber ground blade. It cuts well but is also stout enough to stand up to hard use like batoning.

The sheath is made from injection molded plastic. Like many plastic sheaths, it is bit bulkier than a real kydex sheath would be. However, it is functional. It has adjustable retention (not often seen on injection molded sheaths) and secures the knife well. The included clip works well for belt carry and is adjustable for a number of angles. I removed the clip on mine since I generally carry it in a pack or Kit Bag.

Bargain or Just Cheap?

The RUIKE Hornet F815 bumps right up against our $50 limit for this series but it packs a lot of features not commonly found on bargain fixed blades. It is well designed. It offers a great balance of durability and lightweight. It comes with a functional sheath. It’s a good looking knife with very good fit and finish. The steel is not a bargain basement steel. I call it a BARGAIN and like this knife a lot.

I will be using Amazon as the price base line for this series. All knives were purchased by me from Amazon:

RUIKE Hornet with Black G-10

RUIKE Hornet with Orange G-10

Note: This design is also be available from Sanrenmu, who may actually be the OEM maker of the Hornet, with lower grade 8Cr14Mov steel for considerably less money. I purchased the Hornet because of the better steel and the backing of RUIKE for any potential warranty issues.


Our goal is to represent knives for a variety of uses from EDC, to outdoor, to tactical knives. Do you have a favorite affordable knife? Let us know about it in the comments!

D-Rmor Gear EDK-1A

D-Rmor Gear just launched their first knife – the EDK-1A.

from D-Rmor Gear:

After nearly 6 years of development, the first D-Rmor Gear blade is here.

Embodying all the best features of an everyday carry blade, the EKD-1A was designed from the ground up to be a perfect compliment to a concealed firearm, or as a standalone personal defense tool in non-permissive environments.

At just under 7.25″ in overall length, and a blade length of 2.95″, the EDK-1A is legal in most jurisdictions (please check your own local laws before carrying). With a blade geometry optimized for both the cut and the thrust, it is well-suited to any defensive style. To enhance its utility as a defensive carry tool, it incorporates a Karambit-style finger ring, to speed deployment using gross motor skill.

Precisely CNC machined and available in either D2 or CPM-3V steels (both hardened to approximately 59-60 Rockwell-C and cryogenically tempered), these knives will stand up to extreme use. Handles are secured using stainless chain ring bolts, and are offered with multiple colorways of hand-contoured G10 and Canvas Micarta for a dependable, secure grip in all conditions.

Finally, the blades are laser engraved with the D-Rmor Gear touchmark, and individually serial numbered, then coated with black PVD, Nickel Boron, Titanium Nitride, or Melonite for several lifetimes worth of extreme use.

An optional Kydex retention sheath is available in either black or FDE.

Depending on options, the D-Rmor Gear EDK-1A will be offered for between $369-$399 but the first ten knives will be available at a special price. Please contact D-Rmor Gear today to reserve your blade, limit of one per household.

You can learn more and contact D-Rmor Gear at their website: D-Rmor Gear Website

Bargain or Just Cheap? – Kershaw Emerson CQC-4K

Welcome to Bargain or Just Cheap? This series will review budget friendly knives in a short format. All of the knives will cost less than $50 (in most cases, much less) and will be purchased out of my own pocket. I’ll buy them, carry them, and use them in an attempt to determine if the knife is a bargain or just cheap.


I’ve been carrying and using a Kershaw Emerson CQC-4K mostly because I was able to purchase it for $15. The ultra-low price was my initial attraction to it. It is one of the lowest priced options in the already very budget friendly line of Emerson designed Kershaw produced knives.

Specs:

Lock: Frame Lock

Pocket Clip: Reversible, Tip up only

Steel: 8Cr14MoV

Handle: Textured G-10 front, 410 steel back

Blade length: 3.25 in.

Closed length: 4.2 in.

Open length: 7.4 in.

Weight: 4.1 oz.

Observations from Use

There is a lot to like here. The size is great for EDC – plenty of blade for most EDC tasks, a long enough handle to support four fingers without crowding, and its very pocketable. The Emerson designed Wave Opening Feature works and is a great feature to have. The spear point blade has some belly, plenty of straight edge, and a useful point. The handle is comfortable in the hand. I find that it is also a good looking knife.

8Cr14MoV steel is a budget steel. It performs similarly to AUS-8. It is a stainless steel that sharpens easily. It lacks the edge holding ability of super steels but I find it completely acceptable. It is a solid, budget friendly steel and Kershaw seems to do well with it.

The lock on my example is very good. It locks up somewhat early so there is room for it to wear in and it does pass a spine whack test. The lock bar doesn’t stick and the detent is fairly strong and positive.

Unfortunately, there are some things about this knife that I don’t like. It is heavy for its size due to it’s thick 410 steel lock bar side and a full steel liner under the G-10 handle scale. The thumb disk doesn’t line up well with the relief cut in the handle making it difficult to access. Finally, the primary grind on this knife is a short, hollow grind that leaves the edge fairly thick. It cuts reasonably well but not as well as it could with a higher primary grind.

Bargain or Just Cheap?

If you like Emerson Wave Openers like me, you won’t find a cheaper one, especially with real G-10 handle scales. Unfortunately, the strange spacial relationship between the relief cut in the handle and the thumb disk strikes me as an avoidable design flaw with a very noticeable impact on how easy you can open the knife.

This knife might be a bargain when it can be found around $15-$18 but other than that I’ll say… Just Cheap. If you are going to spend over $20, I would pass unless you are drawn to its smaller size in relation to other Kershaw Emerson models. I think there are better, but larger, options in the Kershaw Emerson line like the CQC-6K which I will review at a later date.

All of the knives for this series will be purchased by me on Amazon: Kershaw Emerson CQC-4K


Do you have a favorite affordable knife? Let us know about it in the comments!

Hard Point Equipment MantiCuda Mountain Man

Hard Point Equipment has introduced a number of new variations of their MantiCuda knife including a new no-frills, budget version called the MantiCuda Mountain Man. This version has all the same dimensions and functionality of the MantiCuda SRT including the G-10 handle slabs and 80CrV2 steel but it lacks the coating. It comes with a more affordable parkerized finish instead.

You can check out the MantiCuda Mountain Man along with the other MantiCuda variants at FistKnife.com.

Bargain or Just Cheap? – Real Steel H6-S1

Welcome to Bargain or Just Cheap? This series will review budget friendly knives for a variety of uses in a short format. All of the knives will cost less than $50 (in most cases, much less) and will be purchased out of my own pocket. I’ll buy them, carry them, and use them in an attempt to determine if the knife is a bargain or just cheap.


I have always been very leery of Chinese knife manufacturers due to their historically poor quality and penchant for knock-off designs. A friend cautioned me about throwing the baby out with the bath water and introduced me to a several Chinese knife manufacturers that are worth a look. One such manufacturer is Real Steel and their H6-S1 is the subject of today’s edition of Bargain or Just Cheap?.

Real Steel offers several variants of the H6 but there is one that I believe really stands out – the H6-S1. This knife floored me with how good it is for the price.

Specs:

Lock: Frame Lock

Pocket Clip: Right pocket, Tip up only

Steel: Sandvik 14C28N

Handle: Textured G-10 front, steel back

Blade length: 3.39 in.

Blade thickness: .12 in.

Open length: 7.76 in.

Weight: 3.8 oz.

Observations from Use

This knife is exceedingly likeable. It is at the upper end of our $50 price limit but it is dripping with great features, hallmarks of quality, and functional design.

The 14C28N is a step up from the blade steel found on many Chinese knives or any budget knife for that matter. This Sandvik steel is easy to sharpen, takes a polished edge VERY well, and holds it well enough for EDC tasks. I was very happy to see a Sandvik steel being used here. The drop point, slightly recurve blade has plenty of spine and features a full flat primary grind. It cuts and slices very well.

The handle is well contoured and comfortable with more than enough room for all your fingers. Both the G-10 and the steel lock side of the knife are thick and sturdy but overall the knife feels and carries very slim. Speaking of G-10, the thumb studs are actually machined G-10 that matches that handle color. They are large and easy to operate. The knife opens easily and smoothly with a flick of the thumb without even having to use your wrist.

The lock on my example is excellent. It looks up with about 60% engagement so it is very sturdy with room to wear in over time. The lock bar features a very unique and very cool feature. It has a disk that at first glance looks like any Hinderer style lock bar stabilizer (a small stop designed to prevent lock bar over travel). Closer inspection reveals the fact that it can be pushed forward into a second position that actually blocks the lock bar from moving completely! In this position, the knife can not close on your hand without some kind of catastrophic breakage. The disk locks in each position with strong detent action so it is extremely unlikely that you will accidentally activate or deactivate it.

This knife is impressively light for a knife of these dimensions. There is some milling on the inside of the steel handle scale to remove weight. A full height flat grind also reduces weight as does a liner-less G-10 handle scale. It is larger in every dimension than the previously reviewed Kershaw Emerson CQC-4K yet it weighs less!

The pocket clip isn’t a true deep carry clip but it does place the knife very low in the pocket which is nice for professional settings. It is very stout and holds the knife securely.

Bargain or Just Cheap?

The fit and finish of this knife is very good. It has better than average steel, better than average materials, clever features, and a very functional design. It also happens to look great! It gives the impression of quality. I’ve seen them as low as $40 but they usually average around $45 for most variants of the H6. Honestly, I would feel good about this knife at twice the price.

There is nothing cheap about this knife other than the price. The Real Steel H6-S1 is most certainly a Bargain.

I will be using Amazon as the price base line for this series. All knives were purchased by me from Amazon: Real Steel H6-S1

 

Note: There are a number of H6 variants and colors available. The features vary significantly from variant to variant. Be sure you are buying the H6-S1 if want the features shown in this review.


Our goal is to represent knives for a variety of uses from EDC, to outdoor, to tactical knives. Do you have a favorite affordable knife? Let us know about it in the comments!

Powered by WordPress. Designed by Woo Themes